 |
6000 and 6500 NON - TURBO
1. STOCK TRACTORS MUST HAVE STOCK APPEARANCE. (EXAMPLE: FORD MUST HAVE FORD ENGINE AND ORIGINAL SHEET METAL INTACT).
2. ENGINE CHANGE IS ALLOWED – ALL ENGINES MUST BE OF THE TYPE USED BY THE FACTORY AND MUST BOLT UP WITHOUT THE USE OF AN ADAPTOR PLATE.
3. EXHAUST MUST DISCHARGE UPWARD 18" ABOVE THE HOOD LINE.
4. CUT TIRES ALLOWED.
5. WEIGHTS:
A. WEIGHTS MAY NOT EXTEND 24" BEYOND FORWARD POINT OF TRACTOR.
B. ALL WEIGHT FRAMES AND WEIGHTS MUST BE STATIONARY AND SAFELY SECURED TO TRACTOR.
C. WEIGHTS MAY NOT EXTEND REARWARD BEYOND REAR TIRES.
D. NO WEIGHTS MAY BE LOCATED IN A POSITION WHICH COULD HINDER SAFE OPERATION OF THE TRACTOR.
E. NO BALLAST WEIGHTS ON TRACTOR’S SEAT AND/OR DECK.
F. NO WEIGHTS OR BRACKETS MAY EXCEED 12" IN WIDTH BEYOND THE TIRES.
G. NO WEIGHTS OR BRACKETS TO BE CLOSER THAN 8" TO DRAWBAR HOOK POINT.
6. MAXIMUM TIRE SIZE 18.4 x 38".
7. ALL TRACTORS MUST BE EQUIPPED WITH WORKING REAR WHEEL BRAKES.
8. FENDERS ARE REQUIRED ON ALL TRACTORS.
9. WHEELIE BARS ARE REQUIRED ON ALL TRACTORS - SPECIFICATION ARE:
A. PADS ON BOTTOM OF BARS TO BE A MINIMUM OF 5 IN. SQ.
B. PADS TO BE A MINIMUM OF 32" REARWARD FROM THE CENTER OF THE REAREND HOUSING. PADS MAXIMUM OF 10" OFF THE GROUND
C. DO NOT CONNECT HITCHES AND WHEELIE BARS.
D. OUTSIDE TO OUTSIDE LENGTH OF PADS TO BE A MINIMUM OF 20".
E. BARS MUST SUPPORT WEIGHT OF TRACTOR FOR WEIGHT CLASS BEING PULLED.
10. CARBURETOR CLARIFICATION FOR ALL NON-TURBO TRACTORS; ONLY ONE CARBURETOR ALLOWED – MUST BE UPDRAFT TYPE.
11. HITCH HEIGHT IS 20". HITCH LENGTH 18" FROM CENTER OF AXLE TO HOOK POINT. DRAWBAR MUST BE RIGID, IN ALL DIRECTIONS. NO MOVEMENT IS ALLOWED WHILE PULLING. DRAWBAR MUST BE PARALLEL TO THE GROUND. HITCH MUST BE HORIZONTAL – NOT VERTICAL.
12. ALL TRACTORS WILL REQUIRE FLYWHEEL PROTECTION IN THE FORM OF EITHER:
A. A SCATTER/SAFETY BLANKET
B. 4" WIDE X 3/8"THICK STEEL AROUND THE FLYWHEEL AREA
13. TORQUE CONVERTERS AND AUTOMATIC SHIFTS ARE PERMITTED.
14. LEGAL FUELS ARE: GASOLINE, DIESEL FUEL, AND LP/PROPANE. ALL FORMS OF NITRO-METHANE AND PROPYLENE OXIDE ARE NOT ALLOWED.
15. KILL SWITCH:
A. FOR SPARK IGNITION ENGINES, THE KILL SWITCH MUST EITHER BREAK OR GROUND THE IGNITION CIRCUIT AND MUST BREAK ELECTRIC POWER TO AN ELECTRIC FUEL PUMP(S) IF SO EQUIPPED
B. FOR DIESEL ENGINES, THE SHUT OFF CABLE MUST ACTIVATE THE AIR SHUTOFF TO THE ENGINE. THE AIR SHUTOFF CABLE MUST BE A POSITIVE-TYPE ENCLOSED CABLE.
C. THE KILL SWITCH/SHUT OFF MUST BE MOUNTED INDEPENDENTLY OF DRAWBAR AND/OR WHEELIE BARS.
D. KILL SWITCH/SHUT OFF TO BE LOCATED IN REAR CENTER OF VEHICLE, 48" ABOVE AND WITHIN 6" OFF CENTER OF POINT OF HOOK.
E. KILL SWITCH/SHUT OFF MUST HAVE A MINIMUM 2" DIAMETER SOLID RING, WITH MINIMUM 1/8" CROSS SECTION THICKNESS, ATTACHED.
16. DRIVER MUST WEAR SHIRT, SHOES AND LONG PANTS.
NOTE: ALL PULLER’S MUST BE SIGNED UP 30 MINUTES BEFORE PULL STARTS
Send E-Mail to: 4x4nut@kinex.net
Copyright © 2005 . All Rights Reserved